Out of stock
Couldn't load pickup availability
Out of stock
Restore Acidic Restoration Cleaner for Ceramic Tile and Groutfrom Bane-Clene® Corp.  Restore Heavy-Duty Acid Tile and Grout Cleaner is a highly concentrated, heavy duty acidic restoration cleaner that makes ceramic tile and grout look like new.
|
Porcelain Tile: Cleaning, Maintenance, Protection and SealingMost types of tiles that are made from clay or a mixture of clay and other materials and then kiln-fired, are considered to be a part of the larger classification called “Ceramic Tiles”. These tiles can be split into two groups, porcelain tiles and non-porcelain tiles. These non-porcelain tiles are frequently referred to as ceramic tiles by themselves, separate from porcelain tiles - confusing!Non-porcelain ceramic tiles are generally made from red or white clay fired in a kiln. They are almost always finished with a durable glaze, which carries the color and pattern. These tiles are used in both wall and floor applications. Non-porcelain ceramic tiles are usually suitable for very light to moderate traffic and generally have a relatively high water absorption rating making them less frost resistant and they are more prone to wear and chipping than porcelain tiles. Porcelain tile is more scratch resistant than ceramic tile. Also, porcelain tile is fired at higher temperatures than ceramic, resulting in superior durability and stain resistance. Porcelain unglazed tile is generally made by the dust pressed method from porcelain clays which result in a tile that is dense, impervious, fine grained and smooth, with a sharply formed face. Porcelain tiles usually have a much lower water absorption rate (less than 0.5%) than non-porcelain ceramic tiles making them frost resistant. Full body porcelain tiles carry the color and pattern through the entire thickness of the tile making them virtually impervious to wear and are suitable for any application from residential to the highest traffic commercial or industrial applications. Because porcelain tile is fire-hardened and quite hard, it can be cleaned at pressures up to 1,450 PSI if the grout is in good condition. Porcelain unglazed tiles are similar to glazed tile, except that their surface is not coated. Full-body porcelain unglazed tiles do not show wear because their color extends throughout the tile, making them ideal for commercial applications. PEI classes range from 0 to 5. The Porcelain Enamel Institute rating scale is not a measurement of quality. It is a scale that clearly indicates the areas of use each manufacturer recommends and has designed their tile to fit. A PEI 2 tile has been designed for areas where very low traffic and soiling is anticipated. In most cases the aesthetic detailing of these tiles is of prime consideration. You will often find high gloss levels, vibrant colorations and metallic elements in this group of tile. Conversely, a PEI 5 tile has been designed for abusive extra heavy foot traffic:
Sealing Ceramic and Porcelain Tile & GroutGlazed tiles are coated with a liquid glass, which is then baked into the surface of the clay. The glaze provides an unlimited array of colors and designs as well as protects the tile from staining. A glazed tile is already stain proof, so there is no purpose to putting on a sealer. However, the grout joint between the tiles is usually very porous and generally made of a cement-based material. Therefore, grout joints typically will need to be sealed and maintained properly to prevent stains and discoloration. Impregnating sealers such as All Purpose Grout Sealer go into the grout joint and protect against water and oil-based stains. Most industry professionals recognize that grout is best protected with a polymer-based sealer, such as Impregnator Pro™ or All Purpose Grout Sealer. If the grout joint is epoxy, a sealer is not necessary. Unglazed porcelain tile should be protected with a penetrating sealer, such as Sta-Clene®, Bullet Proof™ or Impregnator Pro™, including the grout lines. The penetrating sealer is an invisible, stain resistant shield that is absorbed into the surface. Cementitious grout must be sealed to prevent or minimize staining. Leaving these surfaces unsealed may greatly hinder the ability to completely remove stains in the future. Allow new installations to cure for 72 hours prior to applying sealer.
Cleaning Ceramic and Porcelain Tile & Grout
Countertops and VanitiesUse a ph-balanced cleaner such as All Purpose Stone & Tile Cleaner or Revitalizer to keep surfaces clean from everyday soils and stains. Floor SurfacesVacuum or dust frequently using a clean non-treated dry dust mop. Sand, dirt and grit may scratch your tile or build-up on your grout joint leading to discoloration. Mats or area rugs inside and outside an entrance will help minimize the potential damage from these particles. Damp mop your tile floor with a diluted solution of neutral cleaner such as All Purpose Stone & Tile Cleaner or Revitalizer. Try to stay off the floor until it is completely dry, as wet tile floors may be slippery. Bath and Other Wet AreasFor daily maintenance cleaning, use a neutral, ph-balanced cleaner such as All Purpose Stone & Tile Cleaner or Revitalizer to clean everyday soils and stains. In the bath, or other wet areas, using a squeegee after each use can help minimize this build-up. Restoring Ceramic and Porcelain Tile & GroutFor cleaning and restoring old ceramic, porcelain tile and grout to like new condition, we recommend using an acidic cleaner such as Restore™ designed for this surface. This will remove tough soap scum, hard water deposits, grout haze and efflorescence. If you have heavy grease and oil stains, pre-clean using an alkaline cleaner formulated for ceramic and porcelain tile, such as KlenzAll heavy duty alkaline cleaner and degreaser. This will cut through tough grease and soil stains. After restoring your tile and grout, remember to seal with an impregnating sealer such as Bullet Proof or Impregnator Pro, including the grout lines.to guard against future stains. Grout EtchingCeramic and porcelain tile is usually impervious or highly resistant to staining. However, grout may be a different story. Substances that are highly acidic, such as orange juice, coffee, vinegar, wine, tomato-based products, mustard and many soft drinks will most likely leave an “etch,” a chemical reaction that may leave a dull area or mark. Properly sealing the grout will give you time to wipe up a spill to avoid staining, but it cannot prevent etching. In addition, ordinary household cleaners with colored dyes or those containing bleach, ammonia or abrasives are not recommended for ceramic, porcelain tile & grout. They may damage the surface and likely degrade the sealer that is applied to the grout, which provides stain protection. Food SpillsScoop up food with a plastic spoon. Blot with a dry white cloth. Spray the area with a neutral cleaner such as All Purpose Stone & Tile Cleaner or Revitalizer and wipe off excess with a clean cloth. Liquid SpillsBlot up the excess with a clean, dry cloth. Then clean the area with All Purpose Stone & Tile Cleaner or Revitalizer and wipe off excess with a clean cloth. MudLet the mud stain dry completely. Remove dried mud with a soft plastic nylon brush. Then clean the area with All Purpose Stone & Tile Cleaner or Revitalizer and wipe off excess with a clean cloth. Restorative Cleaning of Ceramic and Porcelain Tile & Grout:Depending on the type of soil, stain or other foreign matter present, select one or more of the following options:
What are the DON’Ts of Porcelain Tile?
Problems most frequently encountered with the use of top-coating sealers on porcelain are:
Additional Stone, Ceramic and Porcelain Tile & Grout Information:
Specifications
Safety Data Sheets |
